QUALITY YOU
CAN CERTIFY
Request mill test certificates, material test reports, or a full specification sheet for your project.
Quality Assurance
Every Cupromet product is backed by six international certifications and tested on state-of-the-art laboratory equipment — so your supply chain never carries uncertainty.
Cupromet holds six internationally recognised management system and product certifications — covering quality, environment, safety, medical suitability and pressure equipment compliance.
The world's most recognised quality management standard. Our ISO 9001:2015 certification confirms that every process — from raw material procurement to final dispatch — is governed by a documented, audited quality management system. Ensures consistent product quality, customer satisfaction, and continual improvement across all operations at our Vapi manufacturing facility.
Certifies our manufacturing operations are managed with active environmental responsibility — controlling emissions, waste and resource usage. Non-pollution working conditions ensured throughout the Vapi facility.
International standard for workplace health and safety management. Ensures factory environment is safe for all workers, with hazard identification, risk assessment and emergency preparedness protocols actively in place.
Qualifies Cupromet copper tubes and fittings for use in Medical Gas Pipeline Systems (MGPS) — oxygen, nitrous oxide, medical air, vacuum and CO₂ lines in hospitals, ICUs and operation theatres.
EU Pressure Equipment Directive certificate confirms Cupromet copper tubes and fittings meet EU requirements for pressure-bearing equipment. Essential for export to European markets — contact us for export inquiries and safety-critical pressure systems.
BIS certification under IS 1545 confirms copper tubes conform to Indian National Standards. Mandatory quality mark for government projects, regulated industries and public infrastructure supply contracts across India.
Types K, L, M — for water service, plumbing and HVAC. Varying wall thicknesses for different pressure applications.
For air conditioning and refrigeration. Sets strict interior cleanliness requirements protecting compressor systems.
European standard for seamless copper tubes for water and gas in sanitary and heating applications.
Specifies interior residue ≤ 0.038 g/m² and hardness 45–60 HV5 for ACR coils and pipework tubes.
National Indian standard for copper tubes. Mandatory for government supply and regulated domestic markets.
Seamless copper tube specifically cleaned and certified for oxygen, nitrous oxide and medical gas pipeline systems.
Our in-house quality laboratory is equipped with 16 precision instruments across five testing categories. Every batch is tested before dispatch.
Measures OD and wall thickness to ±0.001 mm. Ensures +0.0/−0.08 mm OD tolerance compliance on every tube.
Optical measurement of cross-section, concentricity and inner-grooved tube profiles.
Verifies annealed coils achieve 45–60 HV5 hardness. Applied to all PCC and LWC batches after annealing.
Measures tensile strength, yield strength and elongation per ASTM B88 and EN 1057 for all temper conditions.
Non-destructive detection of surface cracks, pinholes and laminations. Applied to 100% of critical grade tubes.
Full elemental analysis — Cu, P, Pb, Fe, Bi, Sn and trace elements. Verifies DHP or ETP grade compliance per batch.
Dedicated testing for phosphorus deoxidiser content in DHP copper — critical for brazeability and corrosion resistance.
Gravimetric measurement — solvent flush evaporated and weighed. Mandatory for all ACR coil batches. Medical grade ≤ 0.020 g/m².
Detects surface contamination and lubricant residues under ultraviolet light. Rapid screening before gravimetric testing.
Tests tube leak-tightness and structural integrity under internal water pressure per ASTM B88 and EN 1057.
Detects micro-leaks with compressed nitrogen. Used for refrigerant-grade coils where moisture contamination is critical.
Measures wall thickness non-destructively at any point along the tube — detects localised thinning without cutting.
Quality control is integrated at every production step — not just final inspection. This is how every Cupromet tube meets its certified specification.
OES chemical analysis of incoming copper cathodes before production.
OD and wall measured at every drawing pass. Real-time tolerance monitoring.
Vickers HV5 test on every coil batch. Target: 45–60 HV5.
Residue ≤ 0.038 g/m². End-capped immediately after passing.
Dimensional, visual, documents. MTR issued. JIT dispatch.